| FOX T USW 203 |
| NOTE | The FOX T USW 203 is not compatible with the FOX 3G HD-SDI, FOX 3G DVC, or FOX AV models. |
|
| NOTE | These units are class 1 laser products. They meet the safety regulations of IEC-60825. |
|
| NOTE | *Appropriate HDMI to DVI-D cables or adapters are required for DVI signal input/output. |
|
|
| Optical fiber interconnection between transmitter or fiber matrix switcher and receiver |
|---|
| Number/type | 1 or 2 fiber optic |
| Connectors | 2 LC connectors |
| Operating distance | |
| Singlemode | 30 km (18.75 miles) with singlemode (SM) cables |
| Multimode | 300 m (984') with 62.5 µm OM1 multimode (MM) cables
1 km (3280') with 50 µm OM2 multimode (MM) cables
2 km (6561') with 50 µm OM3/OM4 2000/4700 MHz bandwidth laser optimized multimode cables |
| NOTE | Operating distance is approximate. These are typical maximum distances that may vary depending on factors such as fiber type, fiber bandwidth, connector splicing, losses, modal or chromatic dispersion, environmental factors, and kinks. |
|
| Nominal peak wavelength | 850 nm for MM, 1310 nm for SM |
| Data rate | 4.25 Gbps |
| Maximum pixel clock | 165 MHz |
| Transmission power | |
| Singlemode | -5 dBm, typical |
| Multimode | -5 dBm, typical |
| Maximum receiver sensitivity | |
| Singlemode | -18 dBm, typical |
| Multimode | -12 dBm, typical |
| Optical loss budget | |
| Singlemode | 13 dB, maximum |
| Multimode | 7 dB, maximum |
|
| Video |
|---|
| Digital | |
| Resolution range | 640x480 up to 1920x1200, 480p, 576p, 720p, 1080i, 1080p @ 60 Hz sampled pixel for pixel; higher resolution 2K (2048x1080) @ 60 Hz undersampled |
| Formats | RGB and YCbCr digital video |
| Standards | DVI 1.0, HDMI compliant, HDCP 1.1, CEA-861E |
| Analog | |
| Maximum resolution | Up to 1920x1200 or 1080p @ 60 Hz pixel for pixel |
| Signal Type | VGA-UXGA RGBHV, RGBS, component video |
| Gain | Unity |
| Pixel data bit depth | 8 bits per channel, 3 channels (R, G, B; or YUV) |
|
| Video input and loop-through |
|---|
| Digital | |
| Number/signal type | 2 HDMI, DVI, or DisplayPort |
| Connectors | 2 female HDMI |
| Equalization | Up to 50' of cable |
| Analog | |
| Number/signal type | 1 VGA-UXGA RGBHV, RGBS, component video (YUVp/HDTV)
1 Loop-thru VGA-UXGA RGBHV |
| Connectors | 1 female 15-pin HD |
| Nominal level | 1 Vp-p for Y of component video
0.7 Vp-p for RGB and for R-Y and B-Y of component video |
| Minimum/maximum levels | Analog: 0.3 V to 0.75 Vp-p with no offset, terminated |
| Impedance | 75 ohms |
| Horizontal frequency | 30 kHz to 100 kHz |
| Vertical frequency | 24 Hz to 120 Hz |
| Return loss | <-40 dB @ 5 MHz |
|
| Video output — switched, local |
|---|
| Number/signal type | 1 HDMI switched output |
| Connectors | 1 female HDMI |
| Equalization | Up to 50' of cable |
| Nominal level | 0.8 Vp-p |
|
| Sync |
|---|
| Input type | RGBHV, RGBS, bi- level and tri-level component video (480p, 576p, 720p, 1080i, 1080p) |
| Input level | 2.5 V to 5.0 Vp-p for RGBHV or RGBS
0.6 Vp-p for component video with tri-level sync
0.3 Vp-p for component video with bi-level sync |
| Input impedance | 510 ohms |
| Polarity | Positive or negative (follows input or can be set by user) |
|
| Audio |
|---|
| Gain | |
| Range | Adjustable, -18 dB to +10 dB |
| Default | Balanced output: -6 dB |
| Frequency response | 20 Hz to 20 kHz ±0.5 dB |
| THD + Noise | 0.10% @ 1 kHz at nominal level |
| S/N | >80 dB at maximum output (unweighted) |
| Audio bits per sample | 18 bits per channel, 2 channels (L, R) |
| Sampling rate | 48 kHz |
|
| Audio input |
|---|
| Number/signal type | 1 unbalanced stereo |
| Connectors | (1) 3.5 mm mini stereo jack |
| Impedance | >10k ohms unbalanced |
| Nominal level | -10 dBV (316 mVrms) |
| Maximum level | +7 dBV unbalanced |
| NOTE | 0 dBu = 0.775 Vrms, 0 dBV = 1 Vrms, 0 dBV ≈ 2 dBu |
|
|
| Communications |
|---|
| Serial control ports | |
| Control | 1 RS-232, 3.5 mm captive screw connector, 3 pole (rear panel) |
| Pass-through | 1 RS-232, 3.5 mm captive screw connector, 5 pole (3 pins are used, "RS-232 Over Fiber", shared with alarm port) (rear panel) |
| Baud rate and protocol | |
| Control | 9600 baud, 8 data bits, 1 stop bit, no parity |
| Pass-through | 9600 to 115,200 baud |
| Serial control pin configuration | 1 = Tx, 2 = Rx, 3 = GND |
| USB control port | 1 front panel female mini USB B |
| USB standards | USB 2.0, low speed |
| Contact closure | (1) 3.5 mm captive screw connector, 4-pole |
| Contact closure pin configuration | 1 = input 1, 2 = input 2, 3 = input 3, 4 = GND |
| Program control | Extron control/configuration program for Windows®
Extron Simple Instruction Set (SIS™) |
|
| General |
|---|
| Power supply | External
Input: 100-240 VAC, 50-60 Hz
Output: 12 VDC, 1.5 A, 18 watts |
| Power consumption | |
| Device | 8.0 watts, 12 VDC |
| Device and power supply | 9.8 watts, 100-240 VAC, 50-60 Hz |
| Ambient temperature/humidity | Storage: -40 to +158 °F (-40 to +70 °C) / 10% to 90%, noncondensing
Operating: +32 to +122 °F (0 to +50 °C) / 10% to 90%, noncondensing |
| Cooling | Convection, vents on side panels |
| Thermal dissipation | |
| Device | 25.9 BTU/hr |
| Device and power supply | 32.1 BTU/hr |
| Mounting | |
| Rack mount | Yes, with optional rack shelf |
| Furniture mount | Yes, with optional under desk mounting kit |
| Enclosure type | Metal |
| Enclosure dimensions | 1.75" H x 8.75" W x 6.0" D (half rack wide)
(4.4 cm H x 22.2 cm W x 15.2 cm D)
(Depth excludes connectors) |
| Product weight | 1.0 lbs (0.3 kg) per unit |
| Regulatory compliance | CE, c-UL UL, CE**, C-tick, FCC Class A**, ICES, VCCI,
Complies with the appropriate requirements of RoHS, WEEE |
| Product warranty | 3 years parts and labor |
| Everlast power supply warranty | 7 years parts and labor |
| NOTE | All nominal levels are at ±10%. |
|
| NOTE | Specifications are subject to change without notice. |
|
| (4371-091118-D10) |