| NetPA 204 POE |
|
| Audio system |
|---|
| Frequency response | |
| Through DSP | 20 Hz to 20 kHz, ±0.5 dB |
| Through amplifier | 20 Hz to 20 kHz, ±1 dB |
| THD + Noise | |
| Through DSP | <0.01% @ 1 kHz at maximum output level |
| Through amplifier | 0.1% @ 1 kHz at 3 dB below clipping, 8 ohms |
| S/N | |
| Digital in to speaker out | 100 dB, 20 Hz to 20 kHz at maximum output (unweighted) |
| Crosstalk | <-90 dB @ 1 kHz, fully loaded |
| Volume control | -100 dB to 0 dB (control 0 to 100 in 0.1 dB steps) |
|
| Audio processing |
|---|
| D/A conversion | 24 bit, 48 kHz |
|
| AT ports — audio transport |
|---|
| Transmission type | Dante/AES-67, software selectable |
| Connectivity | 1 RJ-45 connector (2 flows, unicast or multicast) |
| Inputs | 4 channels Rx |
| Outputs | None |
| Audio format | 24-bit uncompressed, selectable at 44.1, 48, 88.2, and 96 kHz sampling rate |
| Latency | Deterministic, based on user selection: 1.0 ms (default), 2.0 ms, 5.0 ms |
| NOTE | 0 dBu = 0.775 Vrms, 0 dBV = 1 Vrms, 0 dBV ≈ 2 dBu |
|
|
| Audio speaker output |
|---|
| Number/signal type | 4 channels, 4 or 8 ohms |
| Connectors | (4) 5 mm captive screw connectors, 2-pole |
| NOTE | These connectors accept wires of 22 AWG to 12 AWG |
|
| Load impedance | 4 ohms minimum |
| Amplifier type | Class D |
| Output power | |
| All channels driven, 8 ohms, 1 kHz, <0.1% THD | |
| PoE++ Power Class 5 (802.3bt) | 20 watts per channel |
| PoE+ Power Class 4 (802.3at) | 18 watts per channel |
| PoE Power Class 3 (802.3af) | 10 watts per channel |
| All channels driven, 4 Ohms, 1kHz, <0.2% THD | |
| PoE++ Power Class 5 (802.3bt) | 20 watts per channel |
| PoE+ Power Class 4 (802.3at) | 20 watts per channel |
| PoE Power Class 3 (802.3af) | 10 watts per channel |
| NOTE | For more information on output power based on specific PoE and output configurations, please refer to the NetPA 204 POE User Guide or PoE configurator at www.extron.com. |
|
|
| Control/remote |
|---|
| Control port | |
| Mute control | Contact closure (1) 3.5mm captive screw connector, 2 pole |
| Pin configuration | Pin 1 = Gnd, pin 2 = mute |
| USB control port | 1 rear panel USB Type-C |
| USB standard | USB 2.0, high speed |
| Ethernet host port | 1 RJ-45 female connector |
| Ethernet data rate | 10/100 Base-T |
| Program control | Extron DSP Configurator Pro control/configuration program for Windows®
Extron Simple Instruction Set (SIS™) |
|
| General |
|---|
| Power input requirements | IEEE 802.3bt Power Class 5 (PoE++), 802.3at Power Class 4 (PoE+),
802.3af Power Class 3 (PoE) |
| Power consumption | |
| PoE++ Power Class 5 (802.3bt) | 38.7 W (max.) |
| PoE+ Power Class 4 (802.3at) | 25.5 W (max.) |
| PoE Power Class 3 (802.3af) | 13.9 W (max.) |
| Ambient temperature/humidity | |
| Storage | -40 to +158 °F (-40 to +70 °C) / 10% to 90%, non-condensing |
| Operating | +32° to +122° F (0° to +50° C) / 10% to 90%, non-condensing |
| Cooling | Convection, no vents |
| Protection | Clip limiter, thermal, short circuit, DC output |
| Mounting | |
| Rack mount | Yes, with optional 1U rack shelf |
| Furniture mount | Yes, with included mounting hardware |
| Pole mount | Yes, with optional pole mounting kit |
| Speaker mount | Yes, with optional ATB 100, V-rail mounted speakers only |
| Enclosure type | Plenum rated, fire-resistant (UL94V-0) metal housing |
| Enclosure dimensions | 1.7" H x 8.7" W x 3.0" D (1U high, half-rack wide)
(43 mm H x 221 mm W x 76 mm D) |
| Product weight | 0.9 lbs (0.4 kg) |
| Regulatory compliance | CE, c-UL, UL, C-tick, EN55032, EN55035, FCC Class B, ICES, VCCI Class B, RoHS, WEEE
Meets UL 62368-1 and BSEN 62368-1.
UL rated for use in plenum airspaces: meets UL 2043 for heat and smoke release. |
| Product warranty | 3 years parts and labor |
| NOTE | All nominal levels are at ±10%.
|
|
| NOTE | Specifications are subject to change without notice. |
|
| (6368-D2) |