| XTP T EU 202 and XTP T MK 202 |
| NOTE | The XTP transmitters can be used with other Extron XTP products, with twisted pair cables connecting the units. |
|
| NOTE | *Appropriate DVI-D to HDMI or DisplayPort to HDMI cables or adapters are required for DVI or DisplayPort signal input. |
|
|
| Video |
|---|
| NOTE | Extron strongly recommends compatibility testing while designing, and before installing, any 3D system. There are several unique 3D formats in use by source devices and display manufacturers. The level of 3D product support is governed by pixel clock, signal format, and communication between source and sink devices. Please contact an Extron Applications Engineer for more information. |
|
| Gain | Unity |
| Resolution range | |
| Digital | Up to 1920x1200*, 2K, or 1080p (HDTV)
* reduced blanking |
| Analog | Up to 1920x1200* or 1080p (HDTV)
* reduced blanking |
| Signal Type | Single-link HDMI (or DVI-D*) |
| Digital video | RGB digital video (DVI and HDMI standards) or Y, Cr, Cb digital component video (HDMI), actively buffered (supports all single-link DVI (if using an optional adapter) and HDMI standards from 640x480 @ 60 Hz to 1900x1200 @ 60 Hz) |
| EDID and DDC | Supports Extended Display Identification Data (EDID) and Display Data Channel (DDC) data using DVI and HDMI standards. EDID and DDC signals are actively buffered. |
| HDCP | Compliant with High-bandwidth Digital Content Protection (HDCP) using DVI and HDMI standards |
| HPD | Supports hot plug detection (HPD) of display as a pass-through signal. |
| Maximum data rate | 6.75 Gbps (2.25 Gbps per color) |
| Maximum pixel clock | 165 MHz |
| Formats | RGB and YCbCr digital video |
| Standards | DVI 1.0, HDMI, HDCP 1.1 |
|
| Video input |
|---|
| Number/signal type | 1 analog RGBHV
1 single link HDMI (DVI-D or DisplayPort*) input |
| Connectors | 1 female 15-pin HD
1 female HDMI type A |
| Nominal level | 0.7 Vp-p for RGB |
| Minimum/maximum levels | 0.3 V to 1.45 V p-p |
| Impedance | 75 ohms |
| Horizontal frequency | 30 kHz to 100 kHz |
| Vertical frequency | 24 Hz to 120 Hz |
|
| Interconnection between transmitter and receiver |
|---|
| Connectors | 1 female RJ-45 per unit |
| Termination standards | TIA/EIA T568B |
| Signal transmission distance | 330' (100 m) using shielded twisted pair cable or XTP DTP 24 cable |
| Cable requirements | Solid conductor, 24 AWG or better |
| Cable recommendations | 400 MHz bandwidth, STP (Shielded Twisted Pair) |
| NOTE | Extron XTP DTP 24 shielded twisted pair cable is stongly recommended for optimal performance. |
|
|
| Audio |
|---|
| Gain | |
| Range | -18 dB to +24 dB |
| Default | Unbalanced output: 0 dB; balanced output +6 dB |
| Frequency response | 20 Hz to 20 kHz, ±0.05 dB |
| THD + Noise | 0.01% @ 1 kHz at nominal level |
| S/N | >90 dB, at maximum output, balanced (unweighted) |
| Crosstalk | <-45 dB @ 20 kHz, -72 dB @ 1 kHz or below |
| Stereo channel separation | >80 dB @ 20 Hz to 20 kHz |
| Sampling rates | 32 kHz, 44.1 kHz, 48 kHz, 96 kHz, 192 kHz |
| Bit depths | 16, 20, 24 bit |
|
| Audio input |
|---|
| Number/signal type | 1 analog stereo, unbalanced or
1 digital audio, embedded from HDMI |
| Connectors | 1 female 3.5 mm mini audio jack
1 female HDMI type A (shared with video input) |
| Source formats | LPCM up to 7.1/24-bit/192 kHz, Dolby TrueHD, Dolby Digital Plus, Dolby Digital EX, Dolby Digital 5.1, Dolby Digital 2/0 Surround, Dolby Digital 2/0, DTS-HD Master Audio, DTS-HD, DTS-ES Discrete 6.1, DTS-ES Matrix 6.1, DTS Digital Surround 5.1, DTS 2 Channel |
| Impedance | >10k ohms, unbalanced, DC coupled |
| Nominal level | +4 dBu (1.23 mVrms) balanced or -10 dBV (316 mVrms) unbalanced |
| Maximum level | +7 dBv unbalanced |
| NOTE | 0 dBu = 0.775 Vrms, 0 dBV = 1 Vrms, 0 dBV ≈ 2 dBu |
|
|
| Communications — transmitter |
|---|
| Serial control port | 1 bidirectional RS-232: 1 rear panel 3.5 mm captive screw connector, 3 pole |
| Baud rate and protocol | 9600 (default) to 115200 baud, 8 data bits, 1 stop bit, no parity |
| Serial control pin configuration | 1 = Tx, 2 = Rx, 3 = GND |
| USB control ports | 1 side panel female mini USB B |
| USB standards | USB 2.0, low speed |
| Program control | Extron control/configuration program for Windows®
Extron Simple Instruction Set (SIS™) |
|
| Communications — External Device (pass-through, unidirectional or bidirectional) |
|---|
| Serial control port input/output | RS-232 (±5 V) via (1) 3.5 mm, 5 pole captive screw connector (uses 3 poles) (connector is shared with IR control port) |
| Serial control port output/input | 1 set of proprietary signals on a female RJ-45 jack |
| Baud rates | Up to 115200 baud |
| Protocol | Data bits = 5 - 8
Stop bits = 1 or 2
Parity = odd, even, none
Flow control = XON, XOFF, none |
| Serial control pin configuration | 1 = Tx, 2 = Rx, 3 = GND |
| IR control port | (1) 3.5 mm, captive screw connector, 5 pole (connector is shared with RS-232 control port)
TTL level (0 to 5 V) modulated infrared control from 30 kHz up to 40 kHz |
| IR control pin configuration | 3 = GND, 4 = IR Tx, 5 = IR Rx |
|
| General |
|---|
| Power supply | External
Input: 100 to 240 VAC, 50-60 Hz
Output: 12 VDC, 1.5 A, 18 watts |
| Power consumption | |
| Device | 8.8 watts, 12 VDC |
| Device and power supply | 10.7 watts, 100-240 VAC, 50-60 Hz |
| NOTE | Each XTP switcher, transmitter, receiver can be powered either locally by an external power supply or remotely using an optional power injector. |
|
| Ambient temperature/humidity | Storage: -40 to +158 °F (-40 to +70 °C) / 10% to 90%, noncondensing
Operating: +32 to +104 °F (0 to +40 °C) / 10% to 90%, noncondensing |
| Cooling | Convection, no vents |
| Thermal dissipation | |
| Device | 29.9 BTU/hr |
| Device and power supply | 36.3 BTU/hr |
| Mounting |
| Furniture or wall mount | Yes, with a EU/MK 2-gang electrical junction box |
| Enclosure type | Metal |
| Enclosure dimensions | |
| XTP T EU 202 | |
| Faceplate | 3.2" H x 6.0" W x 0.5" D (2-gang)
(8.1 cm H x 15.2 cm W x 1.4 cm D) |
| Device | 1.9" H x 4.3" W x 1.4" D
(4.9 cm H x 10.9 cm W x 3.5 cm D)
(Depth excludes connectors. Fits some EU 2-gang boxes.) |
| XTP T MK 202 | |
| Faceplate | 3.4" H x 5.8" W x 0.5" D (2-gang)
(8.6 cm H x 14.7 cm W x 1.4 cm D) |
| Device | 1.9" H x 4.3" W x 1.4" D
(4.9 cm H x 10.9 cm W x 3.5 cm D)
(Depth excludes connectors. Fits some MK 2-gang boxes.) |
| Product weight | 0.7 lbs (0.3 kg) |
| Vibration | ISTA 1A in carton (International Safe Transit Association) |
| Regulatory compliance | CE, c-UL, UL, C-tick, FCC Class A, ICES, KC, VCCI
Complies with the appropriate requirements of RoHS and WEEE. |
| Product warranty | 3 years parts and labor |
| Everlast power supply warranty | 7 years parts and labor |
| NOTE | All nominal levels are at ±10%. |
|
| NOTE | Specifications are subject to change without notice. |
|
| (6580-D8) |