AXI 02 AT

AXI 02 AT

1. Provide a PoE powered Dante® audio interface that shall support two mono analog outputs and a two-channel S/PDIF output, sourced from a Dante audio network.
   1. Two output Dante audio interface with digital to analog conversion up to 96 kHz sampling rate with 24-bit resolution
      1. Output Requirements
         1. Outputs will be routed from a Dante audio network
         2. Shall support two mono line level, balanced or unbalanced outputs that accept 3.5 mm captive screw connectors
         3. Shall provide digital to analog conversion, selectable up to 96 kHz sampling rate with 24-bit resolution
         4. Shall support a two-channel S/PDIF output that duplicates what is routed to the analog outputs, prior to analog output attenuation controls
      2. Audio Device Requirements
         1. Shall provide a Dante to analog output signal-to-noise ratio greater than 95dB measured from 20 Hz to 20 kHz, at maximum output, unweighted
         2. Shall provide a THD+N measurement of less than 0.01% measured at 20 Hz to 20 kHz, at maximum level
      3. Configuration Software Requirements
         1. Shall support PC-based DSP Configurator Software allowing flexible control of the interface’s fixed architecture
         2. Shall provide a Live mode for real-time configuration of parameters
         3. Shall provide an Emulate mode for offline configuration
         4. Shall provide a single window view of all outputs
         5. Shall provide setup and configuration of gain stages and channel mute
         6. Shall provide cut, copy, and paste editing between processing blocks
         7. Shall provide real-time metering of levels within each gain block in Live mode
         8. Shall provide a Meter Bridge window for real-time metering of all output channels with clipping indication in Live mode
         9. Shall provide keyboard-based navigation of configuration software utilizing bidirectional controls, keyboard shortcuts, and spreadsheet software-style commands
         10. Shall provide file saving in both Live and Emulate mode
         11. Shall provide configuration push when switching from Emulation mode to Live mode
         12. Shall provide configuration and file saving of multiple, linked, or networked processors from a single configuration session
      4. Dante Audio Networking Requirements
         1. Shall support incoming channels over a local area network using standard Internet protocols
         2. Shall support Dante Controller software for digital audio network configuration
         3. Shall support Dante Domain Manager network management software for network security and logical segmenting.
         4. Shall support the AES67 standard for interoperability with other devices that also support AES67
         5. Shall provide an RJ-45 connector to support Dante audio network connection and direct interconnection between Dante-enabled products, such as Extron DMP 128 Plus AT units
         6. Shall provide uncompressed digital audio up to 96 kHz sampling rate with 24-bit resolution
         7. Shall provide selectable latency in Dante Controller Software
      5. Configuration Requirements
         1. Shall provide Ethernet configuration via the Dante protocol using DSP Configurator Software
         2. Shall support configuration via USB using DSP Configurator Software
      6. Front Panel Requirements
         1. Shall provide a green LED for power indication
         2. Shall provide an RJ-45 connector to support PoE, Dante audio network connection, and direct interconnection between Dante-enabled products, such as Extron DMP 128 Plus AT units
         3. Shall provide a Configuration port on mini USB B connector
      7. Rear Panel Requirements
         1. Shall provide two balanced/unbalanced analog outputs that accept 3.5 mm captive screw connectors
         2. Shall provide an RCA coaxial connector for two-channel S/PDIF digital audio output
      8. General Requirements
         1. Shall be enclosed in a 1U, eighth rack width plastic enclosure
         2. Shall include an Extron ZipClip™ 100 mounting bracket
         3. Shall support use of optional Extron ZipClip 200 mounting bracket
         4. Shall support use of optional Extron Rack Shelves
         5. Shall meet regulatory compliances
            1. Shall meet safety compliances under CE, c-UL, and UL
            2. Shall meet EMI/EMC compliances under CE, C-tick, FCC Class A, ICES, and VCCI
            3. Shall comply with appropriate requirements of RoHS and WEEE
         6. Shall provide three year parts and labor warranty
   2. Approved device shall be the Extron AXI 02 AT, part number 60-1753-01; no alternates or equals.